Co-ordinate position of sensor in mass of cutting tool

Authors

  • Володимир Іванович Скицюк National Technical University of Ukraine Kiev Polytechnic Institute”, 37 Prospect Peremogy, Kiev 03056, Ukraine, Ukraine
  • Ірина Миколаївна Діордіца National Technical University of Ukraine Kiev Polytechnic Institute”, 37 Prospect Peremogy, Kiev 03056, Ukraine, Ukraine

DOI:

https://doi.org/10.15587/1729-4061.2012.3751

Keywords:

Cutting tool, control, touch

Abstract

The mathematical research, which brings the need to position the sensor in the direction of the maximum of the vibro-acoustic wave in the mass of cutting tools for efficient data signal from the metalworking zone is considered in the article

Author Biographies

Володимир Іванович Скицюк, National Technical University of Ukraine Kiev Polytechnic Institute”, 37 Prospect Peremogy, Kiev 03056, Ukraine

Candidate of Technical Sciences

Department of production equipment

Ірина Миколаївна Діордіца, National Technical University of Ukraine Kiev Polytechnic Institute”, 37 Prospect Peremogy, Kiev 03056, Ukraine

Assistant

Department of production equipment

References

  1. Тимчик Г.С. Відчутники контрольно-вимірювальних систем: монографія. //Тимчик Г.С., Скицюк В.І., Вайнтрауб М.А., Клочко Т.Р. - К.: НТУУ «КПІ», 2008.-240 с.,- Бібліогр.: 232-239 с.
  2. Скицюк В.І., Вимірювання форми деталі за статичного розташування та лінійного детермінованого руху різального інструмента. /Діордіца І.М., Науменко, В.І. Ж. //Вісник НТУУ "КПІ". Серія приладобудування. –2005р.-Вип.29.-С.69-76.

Downloads

Published

2012-04-01

How to Cite

Скицюк, В. І., & Діордіца, І. М. (2012). Co-ordinate position of sensor in mass of cutting tool. Eastern-European Journal of Enterprise Technologies, 2(7(56), 15–18. https://doi.org/10.15587/1729-4061.2012.3751

Issue

Vol. 2 No. 7(56) (2012): Applied mechanics

Section

Applied mechanics

License

Copyright (c) 2014 Володимир Іванович Скицюк, Ірина Миколаївна Діордіца

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.