The research of the extrusion process for forming molded profile from rigid PVC

Authors

  • Геннадій Михайлович Коваленко Limited liability company "Scientific-Production Enterprise " INKOS " Lyubetska str., 33, Chernihiv, Ukraine, 14000, Ukraine
  • Ксенія Геннадіївна Коваленко National Technical University of Ukraine "Kyiv Polytechnic Institute" Peremohi avenue, 37, Kyiv-56, Ukraine, 03056, Ukraine

DOI:

https://doi.org/10.15587/1729-4061.2012.3419

Keywords:

Rigid PVC, extruder, profile size

Abstract

The research of PVC extrusion in the formation of line products was done. The recommendations on selection of technological and structural parameters of the forming tool are offered

Author Biographies

Геннадій Михайлович Коваленко, Limited liability company "Scientific-Production Enterprise " INKOS " Lyubetska str., 33, Chernihiv, Ukraine, 14000

General manager

Ксенія Геннадіївна Коваленко, National Technical University of Ukraine "Kyiv Polytechnic Institute" Peremohi avenue, 37, Kyiv-56, Ukraine, 03056

Postgraduate

Department of Chemistry, polymer and silicate engineering

References

  1. Торнер Р.В. Теоретические основы переработки полимеров [Текст] / Торнер Р.В. – М.: Химия, 1977. – 462 c.
  2. Шенкель Г.П. Шнековые прессы для пластмасс [Текст] / Шенкель Г.П. – Л: Государственное научно-техническое издательство химической литературы, 1962. – 468 с.
  3. Пластические массы [Текст] // Химия. – 1960. – №2. – С. 64.

Downloads

Published

2012-02-01

How to Cite

Коваленко, Г. М., & Коваленко, К. Г. (2012). The research of the extrusion process for forming molded profile from rigid PVC. Eastern-European Journal of Enterprise Technologies, 1(8(55), 11–13. https://doi.org/10.15587/1729-4061.2012.3419

Issue

Vol. 1 No. 8(55) (2012): Energy saving technologies and equipment

Section

Energy-saving technologies and equipment

License

Copyright (c) 2014 Геннадій Михайлович Коваленко, Ксенія Геннадіївна Коваленко

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

The consolidation and conditions for the transfer of copyright (identification of authorship) is carried out in the License Agreement. In particular, the authors reserve the right to the authorship of their manuscript and transfer the first publication of this work to the journal under the terms of the Creative Commons CC BY license. At the same time, they have the right to conclude on their own additional agreements concerning the non-exclusive distribution of the work in the form in which it was published by this journal, but provided that the link to the first publication of the article in this journal is preserved.

A license agreement is a document in which the author warrants that he/she owns all copyright for the work (manuscript, article, etc.).
The authors, signing the License Agreement with TECHNOLOGY CENTER PC, have all rights to the further use of their work, provided that they link to our edition in which the work was published.
According to the terms of the License Agreement, the Publisher TECHNOLOGY CENTER PC does not take away your copyrights and receives permission from the authors to use and dissemination of the publication through the world's scientific resources (own electronic resources, scientometric databases, repositories, libraries, etc.).
In the absence of a signed License Agreement or in the absence of this agreement of identifiers allowing to identify the identity of the author, the editors have no right to work with the manuscript.
It is important to remember that there is another type of agreement between authors and publishers – when copyright is transferred from the authors to the publisher. In this case, the authors lose ownership of their work and may not use it in any way.